The History and Benefits of Stucco
If your home improvement project involves stucco in Southern Highlands, you will want to be sure you find the right contractor for the job. It is always important to hire good contractors, but it is especially important when they will be doing work such as stucco installation, which is not as common as other contracting duties. You need to work with a people who know how do to the job properly, so you can be sure it will get done right the first time.
When you get the bids, make sure to ask if the work will be guaranteed once it is completed. A quality stucco contractor will stand firmly behind their work, so don’t hesitate to ask this question. If the labor and material are not covered by some form of guarantee, you should quickly move on to the next bid. There are plenty of contractors out there who are willing to stand behind their work, so there is no reason to work with one who isn’t.
Stucco can be messy business. Make sure there is a plan in place to protect the rest of your property from the mess that can be made when stucco is put in. You don’t want to be left with a huge cleanup project after your contractor has left the job site, so ask specific questions as to how they will keep the rest of your property as clean as possible.
Hiring a stucco contractor doesn’t need to be a long and drawn out process, as long as you know what you are looking for from the start. Use the points above to guide your search, and only hire a contractor once you are fully satisfied that they are the perfect selection for the work that you need completed.
The Next Generation of EIFS
Aside from roofing failure, the most common source of moisture entering residential community properties is failure of the siding material. In southern California, most siding consists of stucco. Unfortunately, stucco siding systems leak!
Why do builders specify stucco so often?
Stucco became popular in the United States in the early 1800's as an inexpensive and effective means of exterior wall covering over concrete, brick or stone. Today most stucco involves a less expensive method of application; instead of brick or stone, it is applied over open frame construction. "Open frame" means that paper and lathe reinforcement resembling chicken wire is laid over wood-framed walls without sheathing, and then coated with three applications of plaster. This is a low-cost technique, but it has pitfalls.
When you look at a stucco wall, all you see is plaster. The plaster does not keep your home dry; it just protects the waterproofing paper. Yes, paper. In 90 percent of the exterior wall area, all that is keeping your unit dry is paper that is thinner than a business card. Because stucco acts like a sponge, water gains access to the protective paper flashing and will leak into your wall cavity at any tear, backward lap or voided area of the paper.
Almost all stucco leaks can be traced to application error. Errors occur when paper, flashing, windows and other components do not properly overlap (flash) the items directly below them. Leaking will also occur from paper and flashing degradation due to age or excessive moisture entering. Remember, most stucco leaks do not show up on the interior of your unit; the 6-inch space between the stucco and your interior drywall - consisting of fiberglass insulation and wood framing - can hold a lot of water before it shows on the interior. When this occurs, you can expect mold, dry rot and termites to follow.
Leaking within stucco walls usually originates from one of the following sources:
Window leaks in stucco walls are among the most common flashing failures within the entire building structure. These leaks occur from two basic sources: failure of the window frame mechanism itself or improper lapping of the stucco's protective paper system onto the window flanges. Repair commonly requires rehabilitation of the window frame or removal of stucco surrounding the window to correctly apply the paper flashing system.
Miscellaneous wall penetrations
Vents, hose bibs, electrical outlets and light fixtures in stucco walls create a flashing problem during construction. Most of these do not have adequate flanges to overlap the paper flashing properly and were not properly sealed during construction.
Fascia and trim wood
In the past, a common mistake made by builders was to terminate the paper protective system at the point of the fascia board (trim wood) located under the roofline. As the wood ages, it shrinks and splits, allowing moisture to go behind the wood and into the wall.
Wall base leaking
Since stucco acts like a sponge and holds water, it needs to have a "release" flashing at the bottom of the wall, commonly called "weep screed." Most multi-unit complexes constructed prior to 1970 did not have weep screed installed. In many of these structures, trapped water is channeled into the bottom plate of the wall.
Even when weep screed flashing is installed, exterior planter systems are often raised to a level higher than the flashing or the interior floor line. When this occurs, water is forced into the wall structure.
Retrofitted flashing installations
Most managed properties have retrofitted doors, windows, fixtures or repairs that were completed after the original construction. When the stucco around these is patched, the new flashing paper is often overlapped incorrectly, or the old, brittle paper is damaged so much that it is impossible to do proper overlapping. As the new plaster settles and cracks due to improper fastening of wire reinforcement, water finds its way through the plaster and paper and into the wall cavity.
Stucco walls often exhibit cracking at windows, doors or open field areas within the wall. While cracking doesn't necessarily indicate failure of the weather-protection system, the increased exposure to rain water and air-borne pollutants cause the paper to prematurely rot and fail thereby allow moisture intrusion.
Methods of Repair
The difference in cost between repair options can be staggering, so it is critical to seek out an expert in diagnosing and designing an effective solution. Here are three repair options to consider, listed from most to least expensive:
Completely rebuilding a 20-foot by 20-foot section of stucco wall with new flashing may cost between $10,000 and $23,000. Fortunately, this type of repair is seldom necessary. My own company completely rebuilds exterior walls less than 1 percent of the time when addressing stucco failure.
Perhaps the most common type of stucco repair involves removing sections of stucco around windows or flashing transition areas, then applying new flashing, wire reinforcement and plaster. This technique requires meticulous and intensive labor during the demolition and reapplication process. It should include using bituthene pliable membrane at all corners, horizontal surfaces and flashing transition areas. The cost to rebuild three or four flashing transition areas within the same 20-foot by 20-foot section of stucco may cost between $3,000 and $12,000 depending upon the quality of the repair. Doing the job right takes time, which is why this method has the highest failure rate of the three options. In a poorly done rebuild, the new paper flashing is not entirely lapped under the salvage edge of the old paper, and often the lathe wire reinforcement is compromised.
Even when failing sections of stucco and flashing are replaced, the walls can leak due to aging of the surrounding areas of stucco where the paper flashing system is disintegrating. A successful solution is to inject all window, door and miscellaneous flashing penetrations with pliable, durable urethane rubber. The entire wall is then coated from base to roof using an elastomeric coating system such as Thorolastic. Elastomeric coatings waterproof the exterior of the wall and therefore eliminate the necessity to remedy the worn paper flashing system. Repairing a 20-foot by 20-foot section of wall using urethane injection and elastomeric coating may cost between $2,500 and $5,500. When using coatings it is critical that the repair area extends to the roofline so no moisture can become trapped within the stucco. Elastomeric coatings should be reserved only for walls with a history of leaking.
Although troubleshooting leaking stucco walls can be difficult due to the nature of the underlying flashing system, water testing can often provide effective results. Such testing pinpoints failure behind stucco over 95 percent of the time.
Stucco is not going anywhere. You and I will move into our next homes, and chances are they too will be stucco. Fortunately, newer homes are being built with greater care and higher standards. But when leaks do occur, it is important that the method of repair is effective and affordable.
Can You Spray Stucco on Existing Stucco?
Stucco has been used in architectural structures since the Greek and Roman era and during the Renaissance. It spread throughout Europe and gradually became popular in America. Stucco is a finishing plaster composed of sand, lime, water and other ingredients. It is a strong, attractive and damage resistant covering for walls and ceilings. It is an excellent building material for hot areas as it helps to regulate the temperature. It is non-combustible and its surface burning properties include no flame spread and no smoke development.
Currently, there are two distinct types of Stuccoes -
Traditional/Hard Coat Stucco - This is basically cement mixed Stucco. The traditional stucco is durable and able to withstand harsh environments. It is porous and can breathe, so, dries quickly and resists water damage.
Conventionally, lime was used with sand and water. As lime is slightly soluble, the mixture has a self-healing tendency. At present, stuccoes are usually made up of Portland Cement, sand and water resulting in a hard and brittle variety.
To install hard coat stucco, first the substrate is installed followed by a metal lath and then a coat of stucco is applied with a trowel. It is allowed to set and then another coating is applied. Normally, the process involves a scratch coat, a brown coat and a finish coat (may be colored).
Stucco can also be applied on a paper and wire. The coats should be thicker. The first coat (scratch coat) covers the wire. It needs to be scratched as soon as it sets. The second coat (brown coat) gets bonded to this coat and as usual the finish coat is the outermost layer.
Synthetic Stucco - Since 1950s, a number of houses were built using a variety of synthetic materials resembling stucco. Fibers and synthetic acrylics were added to the cement stucco mixture to add strength and flexibility. In general though, the synthetic stuccoes are less heavy and hence, more susceptible to a hard blow. They are a one-coat stucco system unlike the three-coat traditional ones.
The most common one is EIFS or Exterior Insulation & Finish Systems. They are glued or mechanically attached to the substrate and usually composed of three layers. The innermost layer, mostly made up of polystyrene like material, is a foam insulation board. The second layer is a base coating attached to a fiberglass mesh and the final layer is a finish colored coat. It became popular because of its easy installation, low cost and better insulation properties. The only disadvantage is moisture absorption which causes water damage to the building.
A variety of stucco colors/paints are available. Colorants are inorganic pigments which can adapt with the high pH value of cement. They can be either natural like, Ochers and natural earths or artificial, such as man made Iron Oxides. Natural colorants remain unaffected to UV rays and are more pleasant to our eyes. But, the range of shades and the tinting strength is less when compared to manufactured colors. Man made colors, on the other hand, offer a wider range of shades such as dark blues and greens as well as various earthy tones like, yellow, brown and reds. They also possess excellent UV stability due to the presence of inorganic pigments.
Generally, $6-$9 per square foot is the effective cost for stucco installation. A proper inspection of the building is must before the installation. It is always advised to use a better quality beforehand rather than paying later for damage repair.