The Many Benefits Of Stucco
If your home improvement project involves stucco in Boulder City, you will want to be sure you find the right contractor for the job. It is always important to hire good contractors, but it is especially important when they will be doing work such as stucco installation, which is not as common as other contracting duties. You need to work with a people who know how do to the job properly, so you can be sure it will get done right the first time.
When you get the bids, make sure to ask if the work will be guaranteed once it is completed. A quality stucco contractor will stand firmly behind their work, so don’t hesitate to ask this question. If the labor and material are not covered by some form of guarantee, you should quickly move on to the next bid. There are plenty of contractors out there who are willing to stand behind their work, so there is no reason to work with one who isn’t.
Stucco can be messy business. Make sure there is a plan in place to protect the rest of your property from the mess that can be made when stucco is put in. You don’t want to be left with a huge cleanup project after your contractor has left the job site, so ask specific questions as to how they will keep the rest of your property as clean as possible.
Hiring a stucco contractor doesn’t need to be a long and drawn out process, as long as you know what you are looking for from the start. Use the points above to guide your search, and only hire a contractor once you are fully satisfied that they are the perfect selection for the work that you need completed.
The Benefits Of Stucco Installation At Homes
Aside from roofing failure, the most common source of moisture entering residential community properties is failure of the siding material. In southern California, most siding consists of stucco. Unfortunately, stucco siding systems leak!
Why do builders specify stucco so often?
Stucco became popular in the United States in the early 1800's as an inexpensive and effective means of exterior wall covering over concrete, brick or stone. Today most stucco involves a less expensive method of application; instead of brick or stone, it is applied over open frame construction. "Open frame" means that paper and lathe reinforcement resembling chicken wire is laid over wood-framed walls without sheathing, and then coated with three applications of plaster. This is a low-cost technique, but it has pitfalls.
When you look at a stucco wall, all you see is plaster. The plaster does not keep your home dry; it just protects the waterproofing paper. Yes, paper. In 90 percent of the exterior wall area, all that is keeping your unit dry is paper that is thinner than a business card. Because stucco acts like a sponge, water gains access to the protective paper flashing and will leak into your wall cavity at any tear, backward lap or voided area of the paper.
Almost all stucco leaks can be traced to application error. Errors occur when paper, flashing, windows and other components do not properly overlap (flash) the items directly below them. Leaking will also occur from paper and flashing degradation due to age or excessive moisture entering. Remember, most stucco leaks do not show up on the interior of your unit; the 6-inch space between the stucco and your interior drywall - consisting of fiberglass insulation and wood framing - can hold a lot of water before it shows on the interior. When this occurs, you can expect mold, dry rot and termites to follow.
Leaking within stucco walls usually originates from one of the following sources:
Window leaks in stucco walls are among the most common flashing failures within the entire building structure. These leaks occur from two basic sources: failure of the window frame mechanism itself or improper lapping of the stucco's protective paper system onto the window flanges. Repair commonly requires rehabilitation of the window frame or removal of stucco surrounding the window to correctly apply the paper flashing system.
Miscellaneous wall penetrations
Vents, hose bibs, electrical outlets and light fixtures in stucco walls create a flashing problem during construction. Most of these do not have adequate flanges to overlap the paper flashing properly and were not properly sealed during construction.
Fascia and trim wood
In the past, a common mistake made by builders was to terminate the paper protective system at the point of the fascia board (trim wood) located under the roofline. As the wood ages, it shrinks and splits, allowing moisture to go behind the wood and into the wall.
Wall base leaking
Since stucco acts like a sponge and holds water, it needs to have a "release" flashing at the bottom of the wall, commonly called "weep screed." Most multi-unit complexes constructed prior to 1970 did not have weep screed installed. In many of these structures, trapped water is channeled into the bottom plate of the wall.
Even when weep screed flashing is installed, exterior planter systems are often raised to a level higher than the flashing or the interior floor line. When this occurs, water is forced into the wall structure.
Retrofitted flashing installations
Most managed properties have retrofitted doors, windows, fixtures or repairs that were completed after the original construction. When the stucco around these is patched, the new flashing paper is often overlapped incorrectly, or the old, brittle paper is damaged so much that it is impossible to do proper overlapping. As the new plaster settles and cracks due to improper fastening of wire reinforcement, water finds its way through the plaster and paper and into the wall cavity.
Stucco walls often exhibit cracking at windows, doors or open field areas within the wall. While cracking doesn't necessarily indicate failure of the weather-protection system, the increased exposure to rain water and air-borne pollutants cause the paper to prematurely rot and fail thereby allow moisture intrusion.
Methods of Repair
The difference in cost between repair options can be staggering, so it is critical to seek out an expert in diagnosing and designing an effective solution. Here are three repair options to consider, listed from most to least expensive:
Completely rebuilding a 20-foot by 20-foot section of stucco wall with new flashing may cost between $10,000 and $23,000. Fortunately, this type of repair is seldom necessary. My own company completely rebuilds exterior walls less than 1 percent of the time when addressing stucco failure.
Perhaps the most common type of stucco repair involves removing sections of stucco around windows or flashing transition areas, then applying new flashing, wire reinforcement and plaster. This technique requires meticulous and intensive labor during the demolition and reapplication process. It should include using bituthene pliable membrane at all corners, horizontal surfaces and flashing transition areas. The cost to rebuild three or four flashing transition areas within the same 20-foot by 20-foot section of stucco may cost between $3,000 and $12,000 depending upon the quality of the repair. Doing the job right takes time, which is why this method has the highest failure rate of the three options. In a poorly done rebuild, the new paper flashing is not entirely lapped under the salvage edge of the old paper, and often the lathe wire reinforcement is compromised.
Even when failing sections of stucco and flashing are replaced, the walls can leak due to aging of the surrounding areas of stucco where the paper flashing system is disintegrating. A successful solution is to inject all window, door and miscellaneous flashing penetrations with pliable, durable urethane rubber. The entire wall is then coated from base to roof using an elastomeric coating system such as Thorolastic. Elastomeric coatings waterproof the exterior of the wall and therefore eliminate the necessity to remedy the worn paper flashing system. Repairing a 20-foot by 20-foot section of wall using urethane injection and elastomeric coating may cost between $2,500 and $5,500. When using coatings it is critical that the repair area extends to the roofline so no moisture can become trapped within the stucco. Elastomeric coatings should be reserved only for walls with a history of leaking.
Although troubleshooting leaking stucco walls can be difficult due to the nature of the underlying flashing system, water testing can often provide effective results. Such testing pinpoints failure behind stucco over 95 percent of the time.
Stucco is not going anywhere. You and I will move into our next homes, and chances are they too will be stucco. Fortunately, newer homes are being built with greater care and higher standards. But when leaks do occur, it is important that the method of repair is effective and affordable.
Stucco Fireplace - A Sleek And Stylish Fireplace Design
For centuries the imagination of builders and artists alike have been expressed through the versatility and aesthetic appeal of stucco. Stucco can be applied to most any flat or curved surface with a minimum of preparation or fuss. With each application a new work of art is created, showing the skill as well as the personality of the user, allowing any project to be individualized. It’s also a remarkably inexpensive and long-lived wall finish. Many regal homes throughout Europe are finished with stucco that was applied centuries before. This guide will explain how to effectively apply stucco to any exterior wall.
- Good Site For Stucco Supplies
You May Also Like
- How to Apply Stucco
Applying stucco is an easy, low-stress way to beautify your house. You get to exercise some of your creativity, as well as...
- How to Apply Concrete Stucco to Exterior Walls
Stucco is a striking alternative to other exterior house treatments, such as paint. Applying stucco is a project you need to plan...